Canada Electrical Trade Practice Exam

These questions are part of the practice quiz. Start practicing

• What does "ampacity" refer to in electrical terms?
• What is the purpose of a trapeze in electrical installations?
• When should arc-fault circuit interrupters (AFCIs) be installed?
• When should an inspection application and permit be filed according to CEC rules?
• What is the maximum height for overcurrent device operating handles in panel boards within dwelling units?
• What is deemed an acceptable method for splicing wires?
• What must be installed to protect circuits from damage caused by moisture?
• Table D5 provides specifications for what?
• Which device is used to switch from normal power to backup power during installation?
• What are the standard sizes for electrical switches?
• When can a sub busway be joined to a busway without an overcurrent device?
• What is the purpose of an EOL resistor in a circuit?
• What is the purpose of a load center in an electrical installation?
• What must be applied to prevent galvanic corrosion between aluminum and copper conductors?
• Why should high impedance grounding be used in specific installations?
• What type of device typically outputs in a fire alarm system?
• What is the minimum ladder ratio recommended for safety?
• What is the minimum size of a bonding conductor required for a public address system in patient care?
• What is the primary purpose of the Canadian Electrical Code (CEC)?
• What does it indicate when the trouble buzzer rings on a supervised fire alarm system?
• Which organization is responsible for the classification of electrical equipment nameplates?
• What should be verified after completing an electrical installation?
• What document must be submitted for changes to electrical installations?
• What primarily determines the speed of a three-phase squirrel cage motor?
• What is the role of capacitors in electrical systems?
• What is the maximum unguyed projection allowed for a service mast in a consumer's service?
• What is the minimum height for consumer's service conductors' point of attachment?
• What is the function of a panelboard?
• What safety feature is mandatory when installing lighting for swimming pools?
• What is the preferred grounding method for utility service?
• What is the typical insulation resistance measurement for a healthy electrical system?
• What is the required charge level for an emergency battery?
• How can sheath currents be eliminated in a wiring system?
• What size conduit can a hydraulic bender be used to bend to start?
• What is the minimum required working space around electrical panels?
• In what situation could a magnetic contactor chatter?
• What feature is associated with a glue pot?
• When can a contactor be used for high-intensity discharge (HID) lighting?
• What is the rated output of a current transformer (CT)?
• What output voltage does a half wave rectifier provide when 120VAC is input?
• What is the role of a junction box in electrical systems?
• When half of the house lights go dim and half brighten after plugging in a kettle, what is the probable cause?
• How many times the size of pull boxes should a straight-through installation be?
• What is the minimum height for fences, excluding barbed wire?
• What size should bonding conductors for all in-ground pools be?
• What kind of protection does a start/stop station provide?
• What does the term "overload" refer to in electrical systems?
• What is the acceptable installation method for heating cables in outdoor snow melting systems?
• What is the purpose of a ground fault circuit interrupter (GFCI)?
• What is a common cause of electrical fires in residential buildings?
• What type of GFCI receptacle must be installed within 1 meter of a bathtub or shower?
• Where is communication flat cable (CFC) permitted to be used?
• What is an advantage of a three-phase system over a single-phase system?
• What type of board must be used to cover heating cable sets or heating panel sets?
• What is essential for ensuring safety in electrical service installations?
• What is the maximum voltage allowed on an NMD-90 cable?
• What is the primary purpose of overcurrent protection?
• At what temperature is PVC rated?
• When should over-current devices be selected for multiple motors?
• What is the key factor in determining the sizing of service conductors?
• At least how high must the lowest step on a pole be for safe climbing?
• What is the minimum height for overhead conductors above the ground in residential areas?
• What is the primary purpose of using RMC (Rigid Metal Conduit)?
• What does the term "load calculation" entail?
• What type of system provides redundancy in power supply?
• What is the maximum height from the floor to the midpoint of a receptacle used for an electric range?
• In a 120V circuit, how are overloads connected to the contactor?
• What is one important factor to consider when selecting circuit breakers?
• Non-IC pot lights require how much space around them?
• What precaution must be taken when single conductors enter metal boxes through openings over 200A?
• What is the formula to calculate RPM in relation to frequency and number of poles?
• To what voltage are raceways typically rated?
• What type of solder is best for electrical connections and bunch tinning of stranded conductors?
• What is the common color coding for a 120/240V single-phase service in Canada?
• Which factor influences how many motors can be grouped under one set of over-current devices?
• How often should a transfer switch be inspected for functionality?
• What is the maximum allowed temperature for Extra Low Voltage Cable (ELC)?
• Which device is designed to protect appliances from power surges?
• What should be the outcome of adhering to proper electrical codes and practices?
• What should be removed from a sub-panel to ensure proper operation?
• When should permanent wiring be utilized instead of flexible cords?
• How many sizes of electrical switches are commonly recognized?
• How often should smoke detectors be tested?
• What type of wire is suitable for underground installations?
• When is it permissible to splice conductors outside of a box?
• What is the set type designation for heating cables used in snow melting applications?
• What does an isolation transformer do?
• What is the maximum ampacity for over-current devices protecting two or more motors?
• What must be tested and verified before connecting new electrical equipment?
• What type of fire alarm system is activated by a tamper proof switch?
• What does a charred black fuse signify?
• What is the minimum distance from a pool wall for installing a GFCI, phone jack, PA system, and speakers?
• What indicates that a shield is not properly bonded?
• What is the minimum tap conductor length from a junction box to a heater?
• What is an important consideration when selecting wire gauge for a specific load?
• When are two or more grounding electrodes required?
• Which of the following is a key benefit of using surge protection devices?
• Which conductor should be used for high-temperature environments?
• What does a "feeder" refer to in electrical terms?
• What is the voltage limit for low voltage according to the CEC?
• What do evaporators typically absorb heat from?
• How are heat detectors connected to each other in a system?
• What kind of protection is required for outdoor electrical installations?
• What is the primary reason for using circuit breakers instead of fuses in modern electrical systems?
• What does the term "voltage drop" refer to?
• A GFCI receptacle is designed to trip at what current level?
• Which component is typically involved in determining the issues of dimming lights during high-load conditions?
• What is the maximum height allowed for the point of attachment for a consumer's service conductors?
• How far apart should receptacles be installed in a residential living space?
• What do stress cones relieve in an electrical connection?
• What is the role of conductors in electrical installations?
• What is the ambient temperature correction factor used in electrical installations?
• What kind of loads are typically served by a dedicated circuit?
• What protects solid state devices in electrical systems?
• What is the primary purpose of installing a service disconnect?
• What does 'unguyed projection' refer to in electrical installations?
• What is the maximum allowable spacing between fence posts?
• What is typically used to protect overhead conductors from contact with tree branches?
• What is the minimum size of a grounding conductor for a 200A service?
• What type of drawing features a web steel joist?
• What is the maximum allowable load for a 15-amp circuit?
• How should insulation resistance on a cable be checked?
• Which component maintains an alarm system after a power failure?
• What is the maximum voltage rating for a D type plug fuse?
• Under what condition do tools and appliances need not be bonded to ground?
• What is required for a temporary electrical service installation?
• Which type of lighting requires a specific ampacity to load ratio for a contactor?
• What size wire requires a lug to fasten to an electrical device?
• How many screws are typically found on an outdoor cover?
• What is the minimum size of ground grid conductor when installing a grounding system for an outdoor high voltage substation?
• What does a circuit breaker do?
• What does a foggy fuse typically indicate?
• How does a current transformer (CT) typically produce its rated output?
• Which practice is not recommended when working with electrical wiring?
• What does NEC stand for in relation to electrical standards?
• Which type of circuit protection device is often used to prevent ground faults?
• What do fire alarm signal devices contain?
• What are the main components of a typical transformer?
• What could chatter in a magnetic contactor indicate?
• How frequently should electrical panels be inspected according to the CEC?
• A start/stop station is associated with which type of control?
• Which type of conduit is best suitable for use in wet locations?
• What type of disconnecting means can be used for a motor?
• What is a common use for Class 2 conductors?
• Which personal protective equipment (PPE) is necessary for operating a hammer drill?
• For aerial transformers, what is the minimum number of ground rods required?
• What are the two types of grounding systems used in electrical installations?
• What is the maximum number of consumer services that transformers can supply?
• How many watts equal one horsepower?
• What is the maximum size for chain link mesh?
• Which device is designed to prevent electrical shock in wet areas?
• What is the main purpose of a pull box in electrical installations?
• In what scenario is a transfer switch used?
• Which of the following is a requirement for pulling conductors into a raceway?
• What is the maximum distance from which a disconnecting means for hermetic equipment must be visible?
• What must be done to multi-wire branch circuits that share a neutral?
• What is the minimum distance for a drip loop beyond the wet location service head?
• What is the main function of a transformer in electrical systems?
• What is the purpose of a load calculation in electrical installations?
• Where must the 200A metering equipment be installed?
• Which type of conductors is permitted to be in the same raceway as conductive optical fiber cables?
• When AC-90 cable is run through metal studs, what is the minimum distance it must be kept from the edge of the stud?
• Up to what level above the garage floor is considered a Class 1 Zone 2?
• Why is proper cable stripping important?
• What is the maximum circuit breaker size allowed for a residential lighting circuit?
• In electrical installation, what common preventive measure is taken against corrosion?
• What is the maximum voltage to ground allowed in a dwelling unit?
• What is the smallest conductor size that can be pulled into a raceway for fire alarm systems?
• What is the minimum length of conductor that must be left in a box for making connections?
• What is the primary reason for using a ground fault circuit interrupter (GFCI)?
• What should always be used when working on live electrical circuits?
• Which installation is required for all plugs in a bathroom?
• For a general-purpose receptacle, what is the minimum required amperage circuit?
• Which of the following indicates an overload condition in fuses?
• Which wiring method is commonly used for residential installations in Canada?
• Which of the following is a key component in preventing electrical fires?
• In an electrical panel, what is the purpose of a main breaker?
• What action should be taken if a circuit is found to be overloaded?
• Which tables would you reference for voltage drop calculations?
• What table is used to find the conductor correction factor?
• What does "box fill" refer to in electrical installations?
• What is the highest safe rung on a ladder?
• Which application requires the use of a permit prior to commencing work?
• Which of the following describes a suitable method for maintaining an alarm system during outages?
• What materials are typically used to construct service entrance conductors?
• At what maximum current rating must cables be de-rated due to sheath current?
• What is the common use for ductwork in electrical installations?
• In the RPM formula for a motor, what does P represent?
• What is the purpose of using a circuit breaker?
• What is the output voltage when 120VAC is connected to a full wave rectifier?
• What does the term "bonding" refer to in electrical installations?
• A rod electrode shall consist of how many ground rods at minimum?
• How far must a receptacle be located from a pool wall?
• Neutral supported cables should be supported at no more than what length?